How To Inspect Cold Drawn Seamless Pipes

Jun 12, 2022

Leave a message

Cold-drawn seamless pipes are produced by cold-drawing in molds and have many characteristics and advantages. Cold-drawn seamless pipes can also be used in the construction process of various engineering buildings. The key feature of cold-drawn seamless pipes is that they have high strength and high strength. They are used in various industries. In the continuous development to give full play to the key effect. Because there are more critical hazards in the production and operation of cold-drawn seamless pipes, the main use of cold-drawn seamless pipes is also more common. What is the strength of the actual cold drawn seamless pipe?


Among them, the scales commonly used in the strength test of cold-drawn seamless pipes are generally A, B, and C, namely HRA, HRB, and HRC. The strength value is calculated by the above formula: if the A and C scales are used for the experiment, HR=100-e If the B scale is used for the experiment, HR=130-e In the formula, e--the increase of the residual imprint depth, what is the difference between It is indicated by the requirement of 0.002mm, that is, when the tensile force is radially offset by one enterprise (0.002mm), it is equivalent to the change of Rockwell hardness by a number. The larger the e value is, the lower the strength of the metal material is, and on the contrary, the higher the strength is. The application fields of the above three scales are as follows: HRA (diamond cone tension) 20-88HRC (diamond cone tension) 20-70HRB (diameter 1.588mm bearing steel ball tension) 20-100 Rockwell hardness test is now The stage is used in a wide range of ways, in which HRC is used in the steel pipe standard only for the second tensile strength HB. Rockwell hardness can be used to measure metal composite materials from extremely soft to extremely hard. It fills the gap of the Brinell method. It is simpler than the Brinell method and can immediately read the strength value from the case of the strength machine. However, because of its small imprint, the intensity values are not as accurate as the Brinell method. C. Brinell hardness (HV) Brinell hardness test is also a kind of imprinting test method, which is to press a regular quadrangular pyramid diamond tensile force with a relative surface intersection angle of 1360 into the experimental surface layer with the selected experimental force (F). After the required maintenance time, the experimental force is removed, and the length of the two diagonal corners of the imprint is accurately measured. The Brinell hardness value is the quotient obtained by dividing the experimental force by the embossing area. The calculation method is: In the formula: HV--Brinell hardness mark, N/mm2 (MPa); - Arithmetic mean of the two opposite corners of the imprint, mm. The experimental force F selected for Brinell hardness is 5 (49.03), 10 (98.07), 20 (196.1), 30 (294.2), 50 (490.3), 100 (980.7) Kgf (N) and other six grades, which can measure the strength value. The range is 5 to 1000HV. The way of showing is exemplified: 640HV30/20 shows that the Brinell hardness value measured by 30Hgf (294.2N) test force for 20S (seconds) is 640N/mm2 (MPa). The Brinell hardness method can be used to measure the strength of very thin metal composites and skins. It has the key advantages of the Brinell and Rockwell methods, and gets rid of their basic defects, but it is not as simple as the Rockwell method. The Vickers method is rarely used in steel pipe standards. HB is to press the bearing steel ball with a certain diameter (2.5, 5, 10) to the surface of the tested raw material with a certain force, and then accurately measure the diameter of the bearing steel ball on the surface of the tested raw material to distinguish the strength of the raw material. The initial condition of raw materials and quenching, quenching or heat treatment of cold drawn seamless pipes are common in HB. There are three types of HR: A, B, and C3.


You can use the above methods to accurately measure whether your cold-drawn seamless pipe meets the strength standard and whether it meets the conditions. If the standard does not meet the requirements, it will prove that the strength is not qualified.


Send Inquiry